Radio Shack Cordless Telephone 2 Line 900 MHz Handsfree Cordless Phone User Guide

43-1701.fm Page 1 Wednesday, September 20, 2000 8:48 AM  
2-Line 900 MHz Handsfree  
Cordless Phone  
 
43-1701.fm Page 3 Wednesday, September 20, 2000 8:48 AM  
WARNING:  
To reduce the risk of fire or  
shock hazard, do not expose this product to rain  
or moisture.  
CAUTION  
RISK OF ELECTRIC SHOCK.  
!
DO NOT OPEN.  
CAUTION:  
TO REDUCE THE RISK OF  
ELECTRIC SHOCK, DO NOT REMOVE  
COVER OR BACK. NO USER-SERVICE-  
ABLE PARTS INSIDE. REFER SERVICING  
TO QUALIFIED PERSONNEL.  
This symbol is intended to alert  
you to the presence of uninsu-  
lated dangerous voltage within  
the product’s enclosure that might  
be of sufficient magnitude to con-  
stitute a risk of electric shock. Do  
not open the product’s case.  
This symbol is intended to inform  
you that important operating and  
maintenance instructions are  
included in the literature accom-  
panying this product.  
!
Your phone is ETL listed to UL standards and meets all applica-  
ble FCC standards.  
3
Contents  
 
43-1701.fm Page 4 Wednesday, September 20, 2000 8:48 AM  
READ THIS BEFORE INSTALLATION  
Each device that you connect to the phone line draws power  
from the phone line. We refer to this power draw as the device’s  
ringer equivalence number, or REN. The REN is on the bottom  
of the base.  
If you are using more than one phone or other device on the  
line, add up all the RENs. If the total is more than five (three in  
rural areas), your phone might not ring. If ringer operation is im-  
paired, remove a device from the line.  
FCC STATEMENT  
This telephone complies with Part 68 of FCC Rules. You must,  
upon request, provide the FCC registration number and the  
REN to your phone company. These numbers are on the bot-  
tom of the base.  
Note:  
You must not connect your phone to any of the following  
coin-operated systems, party-line systems, or most electronic  
key phone systems.  
In the unlikely event that your phone causes problems on the  
phone line, the phone company can temporarily discontinue  
your service. If this happens, the phone company attempts to  
notify you in advance. If advance notice is not practical, the  
phone company notifies you as soon as possible and advises  
you of your right to file a complaint with the FCC.  
Also, the phone company can make changes to its lines, equip-  
ment, operations, or procedures that could affect the operation  
of this telephone. The telephone company notifies you of these  
4
Contents  
 
43-1701.fm Page 5 Wednesday, September 20, 2000 8:48 AM  
changes in advances, so you can take the necessary steps to  
prevent interruption of your telephone service.  
This equipment complies with the limits for a Class B digital de-  
vice as specified in Part 15 of FCC Rules. These limits provide  
reasonable protection against radio and TV interference in a  
residential area. However, your equipment might cause TV or  
radio interference even when it is operating properly. To elimi-  
nate interference, you can try one or more of the following cor-  
rective measures.  
• Reorient or relocate the receiving antenna.  
• Increase the distance between the equipment and the radio  
or TV.  
• Use outlets on different electrical circuits for the equipment  
and the radio or TV.  
Consult your local RadioShack store if the problem still exists.  
Warning:  
Changes or modifications to this unit not expressly  
approved by the party responsible for compliance could void the  
user’s authority to operate the equipment.  
5
Contents  
 
43-1701.fm Page 6 Wednesday, September 20, 2000 8:48 AM  
ˆ Features  
Your RadioShack 2-Line 900 MHz Handsfree Cordless Phone  
combines the clarity of 900 MHz communication with portability  
and convenience. The phone’s cordless keypad clips to your  
belt or clothing so you can make and answer calls away from  
the unit’s base. The headset allows you to use your hands while  
you talk.  
10-Memory Speed Dial  
— stores up to 10 frequently-called  
phone numbers for easy dialing.  
Ring/Vibrate Dual Mode Selection  
— lets you set the ringer to  
ring, vibrate, or both.  
Receiver Volume Control  
— lets you adjust the volume you  
hear during a call.  
Ample Talk and Standby Time  
— when fully charged (about  
12 hours), the supplied battery provides about 7 hours of talk  
time or 7 days of standby time.  
10-Channel Auto Scan  
— automatically selects a clear chan-  
nel when you make or answer a call.  
Conference  
— lets you talk to parties on both lines at the same  
time.  
Security Access-Protection Code  
— prevents other cordless  
phone users from using your phone line.  
Hearing-Aid Compatible —  
lets you use your phone with hear-  
ing-aids that have a T (telephone) switch.  
6
Features  
 
43-1701.fm Page 7 Wednesday, September 20, 2000 8:48 AM  
ˆ A Quick Look at the Phone  
LOW BATT  
VOLUME  
VOLUME  
8
9
HOLD  
CONF  
L1  
L2  
DC  
Jack  
TELLINE  
1/2  
TELLINE  
2
CHANNEL  
MUTE  
REDIAL/  
PAUSE  
FLASH  
MEMORY  
RING VIB/  
RING/VIB  
ˆ Preparation  
SELECTING A LOCATION  
You can place the phone’s base on a flat surface such as a  
desk, shelf, or table. Select a location that is:  
• near an easily accessible AC outlet  
7
Preparation  
 
43-1701.fm Page 8 Wednesday, September 20, 2000 8:48 AM  
• near a telephone line jack  
• out of the way of normal activities  
• away from electrical machinery, electrical appliances, metal  
walls, filing cabinets, wireless intercoms, security alarms,  
and room monitors  
The base’s location affects the phone’s range. If you have a  
choice of several locations, try each to see which provides the  
best performance.  
Notes:  
Your telephone is designed to be connected to the tele-  
phone network using a compatible modular jack that is Part  
68 compliant.  
Your telephone connects directly to a modular telephone  
line jack. If your phone line jack is not a modular jack, you  
can update the wiring yourself, using jacks and adapters  
available at your local RadioShack store. Or, you can let  
the phone company update the wiring for you.  
• The USOC number of the jack to be installed is RJ14C (for  
TEL LINE 1/2  
) or RJ11C (for both telephone line jacks).  
CONNECTING THE BASE  
You can power the base using the supplied 15V, 300-mA AC  
adapter.  
8
Preparation  
 
43-1701.fm Page 9 Wednesday, September 20, 2000 8:48 AM  
Cautions:  
You must use a Class 2 power source that supplies  
15V DC and delivers at least 300 mA. Its center tip  
must be set to positive and its plug must fit the  
phone's 15V 300 mA jack. Using an adapter that does not  
meet these specifications could damage the phone or the  
adapter.  
!
• Always connect the AC adapter to the phone before you con-  
nect it to AC power. When you finish, disconnect the adapter  
from AC power before you disconnect it from the phone.  
1. If you have a RJ14C modular telephone line jack for 2 line  
usage, plug one end of the supplied 4-pin modular cord into  
TEL LINE 1/2  
. Then plug the other end into the RJ14C mod-  
ular phone line jack.  
If you have two RJ11C modular telephone line jacks for  
using 2 lines, plug one end of the supplied 4–pin modular  
TEL LINE 1/2  
cord into  
, and one end of the supplied 2–pin  
TEL LINE 2  
modular cord into  
. Then plug the modular cords’  
other ends into the RJ11C modular phone line jacks.  
2. Lift the base’s antenna to a vertical position.  
CONNECTING AND CHARGING THE  
BATTERY PACK  
The phone comes with two rechargeable nickel-cadmium bat-  
tery packs. You must connect the battery pack and charge it for  
at least 12 hours for the first time before you use the phone.  
9
Preparation  
 
43-1701.fm Page 10 Wednesday, September 20, 2000 8:48 AM  
To connect the battery pack, line up  
the slots on the battery pack with  
the posts on the back of the keypad.  
Press down and slide the battery  
pack forward until the latch clicks.  
Battery  
Pack  
Battery  
Charging  
Slot  
To charge the battery  
pack, place the keypad in  
the base’s front charging  
slot. The CHARGE indica-  
tor at the front of the unit  
lights.  
Antenna  
CHARGE  
Keypad  
Charging  
Slot  
L1  
L2  
To charge the spare bat-  
tery pack, place it in the  
rear charging slot with its  
latch end facing down and  
CHARGE  
PAGE  
its contacts toward the rear of the base. The CHARGE indicator  
between the two slots lights.  
Notes:  
• Recharge the battery pack anytime the LOW BATT indica-  
tor flashes, or if the keypad beeps while you are on the  
phone.  
• When you first use the phone after charging or recharging  
the battery pack, the phone might not work. Return the key-  
pad to the base for about 5 seconds to reset the security  
access-protection code.  
• About once a month, fully discharge the battery pack by  
keeping the phone off the base until the LOW BATT indica-  
tor flashes, or if the keypad beeps while you are on the  
10  
Preparation  
 
43-1701.fm Page 11 Wednesday, September 20, 2000 8:48 AM  
phone. Otherwise, the battery pack loses its ability to fully  
recharge.  
• If the front CHARGE indicator does not light when you  
place the keypad on the base, be sure the battery pack and  
AC adapter are correctly and securely connected. Also,  
check the charging contacts on the keypad and base. If the  
contacts are dirty or tarnished, clean them with a pencil  
eraser.  
• If the battery pack becomes completely discharged or the  
base loses power while the keypad is away from it, place  
the keypad on the base for about 5 seconds to reset the  
security access protection code. If the keypad loses power,  
leave it on the base to charge the battery pack.  
• If you are not going to use your phone for an extended  
period of time, disconnect its battery pack. This helps  
increase the battery pack’s usable life.  
Recharging the Battery Pack  
The battery pack should last about a year. If the battery pack  
does not hold a charge for more than 2 hours after an overnight  
charge, replace it. You can order a replacement battery pack  
through your local RadioShack store.  
Note:  
To avoid losing numbers stored in memory, you must in-  
stall and begin charging the new battery pack within 2 minutes  
of removing the old one.  
1. To remove the old battery pack, press the latch release,  
then slide the battery pack off the keypad.  
11  
Preparation  
 
43-1701.fm Page 12 Wednesday, September 20, 2000 8:48 AM  
2. To connect the new battery pack, line up the slots on the  
battery pack with the posts on the keypad, then press down  
and slide it forward until the latch clicks.  
3. Charge the battery pack for 12 hours before using it.  
Cautions:  
• Be careful not to short the battery pack by touching it with  
conducting materials, such as rings, bracelets, and keys.  
The battery pack or conductor might overheat and burn.  
• Do not dispose of the battery pack in a fire because it might  
explode.  
• Do not open or mutilate the battery pack.  
Note:  
If you have trouble replacing the battery pack, take the  
phone to your local RadioShack store for assistance.  
®
Important:  
The EPA certified RBRC Battery Re-  
cycling Seal on the nickel-cadmium (Ni-Cd) bat-  
tery indicates RadioShack is voluntarily  
participating in an industry program to collect and  
recycle these batteries at the end of their useful  
life, when taken out of service in the United States or Canada.  
The RBRC program provides a convenient alternative to placing  
used Ni-Cd batteries into the trash or the municipal waste  
stream, which may be illegal in your area. Please call 1-800-  
THE-SHACK (1-800-843-7422) for information on Ni-Cd battery  
recycling and disposal bans/restrictions in your area.  
RadioShack’s involvement in this program is part of the compa-  
ny’s commitment to preserving our environment and conserving  
our natural resources.  
12  
Preparation  
 
43-1701.fm Page 13 Wednesday, September 20, 2000 8:48 AM  
CONNECTING AND ADJUSTING THE  
HEADSET  
1. Insert the tabs on the headset holder  
into the slots on the back of the base  
and snap the holder into place.  
2. Insert the headset’s plug into the jack  
on the side of the keypad.  
3. Place the headset on your head  
with the earpiece over either ear.  
4. Adjust the headset band until it  
rests with almost no pressure  
on your ear and the top of your  
head.  
5. If the headset is loose, press in slightly to tighten it. If it is  
tight, gently pull the headset band out to loosen it.  
6. Hold the headset in place and adjust the microphone boom  
until it is about even with (but not in front of) your mouth.  
Experiment until you find the most comfortable position.  
Caution:  
The microphone boom swivels on the headset. Do not  
bend the microphone boom while you adjust it.  
Note:  
When you are not using the headset, place it on the  
headset hanger. Otherwise (if you set it on a flat surface, for ex-  
ample), you might have to repeat these adjustments.  
13  
Preparation  
 
43-1701.fm Page 14 Wednesday, September 20, 2000 8:48 AM  
SETTING RING/VIBRATE/DUAL  
RING VIB  
You can adjust the keypad’s ringer mode from  
to  
RING/VIB  
.
VIB  
With the ringer set to  
when receiving call.  
, the phone vibrates instead of ringing  
RING/VIB  
With the ringer set to  
when receiving call.  
, the phone rings and vibrates  
Note:  
The keypad does not vibrate when it is on the base.  
TURNING THE RINGERS ON OR OFF  
L1 RINGER OFF/ON  
L2 RINGER OFF/ON  
and  
The keypad’s ringer  
on the base control. To have the phone ring when a call comes  
RINGER  
ON  
. To keep the phone  
in, set  
on the desired line to  
RINGER  
OFF  
.
from ringing, set  
on the desired line to  
RINGER  
OFF  
, the phone does not ring for incoming  
With  
set to  
calls, but you can still make outgoing calls. If you hear an exten-  
sion telephone ring, you can answer the incoming call on this  
phone. The L1 or L2 indicator flashes until you answer the call.  
Note: RINGER  
If  
OFF  
RING VIB RING/VIB  
is set to  
is set to  
and  
RING/VIB  
, the keypad still vibrates when a call comes in.  
VIB  
or  
SETTING THE DIALING MODE  
TONE/PULSE  
Set  
on the side of the base for the type of service  
you have. If you are not sure which type you have, do this sim-  
ple test after charging the battery pack.  
14  
Preparation  
 
43-1701.fm Page 15 Wednesday, September 20, 2000 8:48 AM  
TONE/PULSE  
TONE  
.
1. Set  
to  
L2  
so the indicator for that line lights and listen  
L1  
2. Press  
or  
for a dial tone.  
3. Press any number other than or .  
Note:  
0
1
If your phone system requires that you dial an  
access code (9, for example) before you dial an outside  
number, do not press the access code either.  
If the dial tone stops, you have touch-tone service. If the  
dial tone continues, you have pulse service.  
L1  
L2  
.
4. Press  
or  
TONE/PULSE  
TONE  
. If  
.
5. If you have tone service, leave  
you have pulse service, set  
set to  
TONE/PULSE  
PULSE  
to  
Note:  
Return the keypad to the base for at least 5 seconds after  
you set the service type.  
ˆ Operation  
Before you use the phone, put the headset on and adjust it as  
needed (see “Connecting and Adjusting the Headset” on  
Page 13).  
L1  
L2  
or . You hear a  
To make a call, select a line by pressing  
dial tone and the indicator for that line lights. Dial the number  
you want to call.  
15  
Operation  
 
43-1701.fm Page 16 Wednesday, September 20, 2000 8:48 AM  
When you receive a call on a line, the light for that line flashes  
and the phone rings or vibrates (if you set the ringer for that line  
ON  
to  
). Press the button for the ringing line to answer the call.  
The indicator for that line lights.  
Notes:  
• When you are using one line and a call comes on the other  
line, the phone beeps or vibrates and the indicator of that  
line flashes. You can hold the line you are using and  
answer the call. (See “Using Hold” on Page 17.)  
• When you press a button, a single tone indicates that the  
phone has accepted the command. Three tones indicate  
that you pressed a button in error or there is severe inter-  
ference. (See “Changing Channels” on Page 18.)  
• If interference is severe, the keypad might lose communi-  
cation with the base and the call might disconnect. If this  
happens, return the keypad to the base for about 5 sec-  
onds to reset the security access-protection code.  
ADJUSTING THE HEADSET’S VOLUME  
VOLUME  
To adjust the headset’s volume, repeatedly press  
8
VOLUME  
or  
9 during a call until the sound level is comfortable.  
You can set the headset’s volume to one of four levels, and it  
remains set even after you hang up.  
Note:  
The keypad sounds 3 beeps when you reach the lowest  
or highest listening level.  
16  
Operation  
 
43-1701.fm Page 17 Wednesday, September 20, 2000 8:48 AM  
USING HOLD  
HOLD  
lets you use the other line without disconnecting the call.  
HOLD  
You can alternate between the two lines by pressing  
then the button for the desired line.  
,
HOLD  
1. To place a call on hold, press  
line flashes.  
. The indicator for that  
2. To release a line from hold and continue your conversation,  
press that line’s button.  
Notes:  
• If you press the other line’s button without first pressing  
HOLD  
, the first call is disconnected.  
• If you hold the line for 1 minute, the keypad sounds  
three beeps every 30 seconds. If you hold the line for 8  
minutes, the keypad beeps for 2 minutes. Press that  
line’s key to release the line from hold, or the line will be  
automatically disconnected within 2 minutes. If you still  
HOLD  
want to hold the line, press  
cycle.  
again to repeat the  
USING CONFERENCE  
You can talk to both lines at the same time.  
1. Use one line and hold the other line, or put both lines on  
hold.  
CONF  
2. Press  
. The indicators for both lines light.  
17  
Operation  
 
43-1701.fm Page 18 Wednesday, September 20, 2000 8:48 AM  
3. To hang up one line, press the other line’s key. Press the  
key again to hang up both lines.  
CHANGING CHANNELS  
L1  
L2  
or , the phone automatically selects  
Every time you press  
a clear channel from the 10 it uses for communication between  
the headset and the base.  
CHAN-  
If you hear interference during a call, repeatedly press  
NEL  
to change the channel until you get a clear one.  
USING REDIAL  
L1  
L2  
RE-  
then  
To quickly redial the last number dialed, press  
or  
DIAL/PAUSE  
.
The redial memory holds up to 32 digits, so you can redial long-  
distance as well as local numbers. The redial memory can also  
store tone entries (see“Using Tone Services on a Pulse Line”  
on Page 19) and pause entries (see “Entering a Pause in Mem-  
ory Number” on Page 21).  
REDIAL/PAUSE  
If the number you dialed is busy, press  
without  
hanging up the phone to redial the number. The dial tone  
sounds for about 2 seconds, then the phone redials the number.  
USING MUTE  
To talk to someone else in the room without the person on the  
other end of the phone line hearing your conversation, press  
MUTE  
. The indicator for the line you are using flashes. Press  
again to resume your phone conversation.  
MUTE  
18  
Operation  
 
43-1701.fm Page 19 Wednesday, September 20, 2000 8:48 AM  
USING FLASH  
FLASH  
provides the electronic equivalent of a switchhook signal  
for special phone services such as Call Waiting.  
FLASH  
For example, if you have Call Waiting, press  
to answer  
an incoming call without disconnecting the current call. Press  
FLASH  
again to return to the first call.  
Note:  
FLASH  
If you do not have any special phone services, pressing  
might disconnect your current call.  
USING TONE SERVICES ON A PULSE LINE  
Some special services, such as bank-by-phone, require tone  
signals. If you have pulse service, you can still use these tone  
services by following these steps.  
1. Dial the service’s main number.  
/TONE  
2. When the service answers, press ∗  
. Any additional  
numbers you dial are sent as tone signals.  
L1  
L2  
. The phone  
3. After you complete the call, press  
automatically resets to pulse dialing.  
or  
USING PAGE  
You can send a page to the keypad to locate it when it is away  
from the base and not in use.  
PAGE  
1. Press  
on the base. The keypad rings for about 15  
seconds.  
19  
Operation  
 
43-1701.fm Page 20 Wednesday, September 20, 2000 8:48 AM  
PAGE.  
2. Press and hold  
The keypad rings for about 1 minute.  
PAGE  
3. Press any key on the keypad or  
silence it.  
on the base to  
MEMORY DIALING  
You can store up to 10 numbers of up to 16 digits each in the  
phone’s memory.  
Notes:  
To keep your accounts secure, we recommend you do not  
store your personal access code for services such as bank-  
by-phone in a memory location.  
• When storing numbers for special services (such as alter-  
nate long-distance or bank-by-phone), store the service’s  
main phone number in one memory location and numbers  
for additional information in other locations.  
Storing a Number in Memory  
MEMORY  
1. Press  
on the keypad.  
2. Enter the desired number (up to 16 digits).  
MEMORY  
3. Press  
again.  
1 0  
4. Press the memory location ( – ). Two long beeps sound.  
Note:  
0
For the 10th memory location, press .  
20  
Operation  
 
43-1701.fm Page 21 Wednesday, September 20, 2000 8:48 AM  
5. You can write down the stored numbers on the memory  
index card underneath the base.  
Note:  
If you hear three short beeps, you did not store the num-  
ber successfully. Start again from Step 1.  
Entering a Pause in Memory Number  
In some telephone systems, you must dial an access code (9,  
for example) and wait for a second dial tone before you can dial  
an outside number. You can store the access code with the  
phone number. However, if you do, you should also store a  
pause after the access code to allow the outside line time to  
REDIAL/PAUSE  
connect. After entering the access code, press  
to enter a 2-second pause.  
Dialing a Stored Number  
L1  
L2  
.
1. Press  
or  
MEMORY  
2. When you hear the dial tone, press  
, then the  
1 0  
memory location number ( – ). The phone dials the num-  
ber.  
Chain-Dialing Service Numbers  
For quick recall of numbers for special services (such as alter-  
nate long distance or bank by phone), store each group of num-  
bers in its own memory location.  
To call special services, dial the service’s main number. At the  
MEMORY  
appropriate place in the call, press  
, then the number  
for the location where the additional numbers are stored.  
21  
Operation  
 
43-1701.fm Page 22 Wednesday, September 20, 2000 8:48 AM  
Note:  
If you use pulse dialing, be sure you have stored a tone  
entry in another memory location (see “Using Tone Services on  
a Pulse Line” on Page 19).  
Testing Stored Emergency Numbers  
If you store an emergency service’s number (police department,  
fire department, ambulance) and you want to test the stored  
number, make the test call during the late evening or early  
morning to avoid peak demand periods. Remain on the line to  
explain the reason for your call.  
ˆ Troubleshooting  
We do not expect you have any problem with your telephone,  
but if you do, the following suggestions might help.  
Problem  
Suggestion  
Move the keypad closer to the base. Raise the  
base’s antenna to a vertical position.  
Ensure the phone’s modular cord and the AC  
adapter are correctly and securely connected.  
The keypad  
does not  
work.  
Recharge the keypad’s battery pack.  
Reset the security access-protection code by plac-  
ing the keypad on the base for about five seconds.  
Keep the headset and base away from interference  
sources such as computers, remote control toys, wire-  
less alarm systems, wireless intercoms and room moni-  
tors, fluorescent lights, and electrical appliances.  
The call is  
noisy.  
22  
Troubleshooting  
 
43-1701.fm Page 23 Wednesday, September 20, 2000 8:48 AM  
Problem  
Suggestion  
Turn off the interfering device.  
There is  
severe inter-  
ference.  
Move the keypad closer to the base. Hang up and  
redial the number.  
CHANNEL  
to change the channel.  
Press  
Ensure the base’s antenna is raised and is not  
touching a metal surface.  
The range  
decreases.  
Recharge the keypad’s battery pack.  
You can  
TONE/PULSE  
receive calls, Set  
correctly for the type of service you  
but cannot  
make calls.  
have (see “Setting the Dialing Mode” on Page 14).  
If you still have problems, disconnect the phone. If other phones  
on the same line work properly, the fault is in this phone or its  
installation. If you cannot locate the problem, take your phone to  
your local RadioShack store for assistance.  
LIGHTNING  
Your telephone has built-in lightning protection to reduce the  
risk of damage from surges in telephone line and power line  
current. This lightning protection meets or exceeds FCC re-  
quirements. However, lightning striking the telephone or power  
lines can damage your telephone.  
Lightning damage is not common. Nevertheless, if you live in an  
area that has severe electrical storms, we suggest that you un-  
plug your phone before storms to reduce the possibility of dam-  
age.  
23  
Troubleshooting  
 
43-1701.fm Page 24 Wednesday, September 20, 2000 8:48 AM  
Limited One-Year Warranty  
This product is warranted by RadioShack against manufacturing defects in material and work-  
manship under normal use for one (1) year from the date of purchase from RadioShack com-  
pany-owned stores and authorized RadioShack franchisees and dealers. EXCEPT AS  
PROVIDED HEREIN, RadioShack MAKES NO EXPRESS WARRANTIES AND ANY IMPLIED  
WARRANTIES, INCLUDING THOSE OF MERCHANTABILITY AND FITNESS FOR A PAR-  
TICULAR PURPOSE, ARE LIMITED IN DURATION TO THE DURATION OF THE WRITTEN  
LIMITED WARRANTIES CONTAINED HEREIN. EXCEPT AS PROVIDED HEREIN, Ra-  
dioShack SHALL HAVE NO LIABILITY OR RESPONSIBILITY TO CUSTOMER OR ANY  
OTHER PERSON OR ENTITY WITH RESPECT TO ANY LIABILITY, LOSS OR DAMAGE  
CAUSED DIRECTLY OR INDIRECTLY BY USE OR PERFORMANCE OF THE PRODUCT OR  
ARISING OUT OF ANY BREACH OF THIS WARRANTY, INCLUDING, BUT NOT LIMITED  
TO, ANY DAMAGES RESULTING FROM INCONVENIENCE, LOSS OF TIME, DATA, PROP-  
ERTY, REVENUE, OR PROFIT OR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSE-  
QUENTIAL DAMAGES, EVEN IF RadioShack HAS BEEN ADVISED OF THE POSSIBILITY  
OF SUCH DAMAGES.  
Some states do not allow limitations on how long an implied warranty lasts or the exclusion or  
limitation of incidental or consequential damages, so the above limitations or exclusions may  
not apply to you.  
In the event of a product defect during the warranty period, take the product and the Ra-  
dioShack sales receipt as proof of purchase date to any RadioShack store. RadioShack will, at  
its option, unless otherwise provided by law: (a) correct the defect by product repair without  
charge for parts and labor; (b) replace the product with one of the same or similar design; or (c)  
refund the purchase price. All replaced parts and products, and products on which a refund is  
made, become the property of RadioShack. New or reconditioned parts and products may be  
used in the performance of warranty service. Repaired or replaced parts and products are war-  
ranted for the remainder of the original warranty period. You will be charged for repair or re-  
placement of the product made after the expiration of the warranty period.  
This warranty does not cover: (a) damage or failure caused by or attributable to acts of God,  
abuse, accident, misuse, improper or abnormal usage, failure to follow instructions, improper  
installation or maintenance, alteration, lightning or other incidence of excess voltage or current;  
(b) any repairs other than those provided by a RadioShack Authorized Service Facility; (c) con-  
sumables such as fuses or batteries; (d) cosmetic damage; (e) transportation, shipping or in-  
surance costs; or (f) costs of product removal, installation, set-up service adjustment or  
reinstallation.  
This warranty gives you specific legal rights, and you may also have other rights which vary  
from state to state.  
RadioShack Customer Relations, 200 Taylor Street, 6th Floor, Fort Worth, TX 76102  
We Service What We Sell  
12/99  
43-1701  
RadioShack Corporation  
Fort Worth, Texas 76102  
08A00  
Printed in China  
 

Radio Shack Cordless Telephone ET 553 User Guide
Regency Indoor Fireplace F2400 User Guide
Ricoh All in One Printer FAX5600L User Guide
Rosewill Switch RHUB 310 User Guide
Samson Headphones CO1U User Guide
Samsung Air Conditioner ACC2400C User Guide
Samsung Camcorder ES65 User Guide
Samsung Car Video System 460TMN User Guide
Sanyo Digital Camera VCC HD4000 User Guide
Sanyo VCR VWM 900 User Guide