Legacy Car Audio LDCS 91 User Manual

LDCS 91  
OWNER'S MANUAL  
Mobile Video System  
CAR DVD/VCD/CD/MP3 CASSETTE RECEIVE  
ST  
TAPE IN  
POWER  
MODE  
SETUP  
CLK  
STOP  
PLAY/PAUSE  
ANGLE  
MUTE  
BAND  
OSD  
ST/MO  
REPEAT  
3 IN 1  
TITLE/PBC  
A/P  
LO/DX  
EQ  
SEL  
DVD & CASSETTE & RADIO  
+
UP  
F.FWD  
NEXT  
VOL  
ENTER  
DN  
F. BWD  
PREV.  
VOL  
-
1
2
6
9
3
4
5
7
8
SW  
MENU  
+10  
0
DVD/VCD/CD/MP3 PLAYER WITH  
AUTO REVERSE CASSETTE WITH  
AM/FM-STEREO DIGITAL PLL TUNING RADIO  
WITH ANTI-THEFT FLIP DOWN DETACHABLE PANEL  
SAFETY INFORMATION  
CAUTION:  
THIS DVD PLAYER IS A CLASS I LASER PRODUCT. HOWEVER THIS DVD PLAYER  
USES A VISIBLE/INVISIBLE LASER BEAM WHICH COULD CAUSE HAZARDOUS  
RADIATION EXPOSURE IF DIRECTED. BE SURE TO OPERATE THE DVD PLAYER  
CORRECTLY AS INSTRUCTED.  
USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES  
OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS  
RADIATION EXPOSURE. DO NOT OPEN COVERS AND - DO NOT REPAIR  
YOURSELF. REFER SERVICINGTO QUALIFIED PERSONNEL.  
WARNING:  
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS  
EQUIPMENT TO RAIN OR MOISTURE.  
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, AND ANNOYING  
INTERFERENCE, USE ONLY THE RECOMMENDED ACCESSORIES.  
THIS DEVICE IS INTENDED FOR CONTINUOUS OPERATION.  
This product incorporates copyright protection technology that is protected by  
method claims of certain U.S. patents and other intellectual property rights owned  
by Macrovision Corporation and other rights owners. Use of this copyright protection  
technology must be authorized by Macrovision Corporation, and is intended for  
home and other limited viewing uses only unless otherwise authorized by Macrovision  
Corporation. Reverse engineering ordisassembly is prohibited.  
REGION MANAGEMENT INFORMATION:  
This DVD Player is designed and manufactured to respond to the Region Management  
Information that is recordedon a DVD disc. If the Region number described on the  
DVD disc does not correspond to the Region number of this DVD Player, this DVD  
Player cannot play this disc.  
2
DISC NOTES  
Disc formats supported by this player  
Label side up  
DVD  
12 cm disc  
(Single-sided disc only)  
Video CD  
12 cm disc  
CD  
Do not touch  
the underside  
of the disc  
12 cm disc  
MP3  
12 cm disc  
Discs which cannot be played with this  
player  
Do not bend  
• DVD-ROM  
• DVD-R/DVD-RAM  
• CDV  
• CD-G  
Wipe the disc from center  
toward the outside edge  
Handling and Cleaning  
• Dirt, dust, scratches and warping disc  
will cause misoperation.  
• Do not place stickers or make  
scratches on discs.  
Preparing New Discs with Rough  
Spots  
• Do not warp discs.  
A new disc may have rough edges on its  
inside and outside edges. If a disc with  
rough edges is used, the proper setting  
will not be performed and the player will  
not play the disc. Therefore, remove the  
rough edges in advance by using a ball  
point pen or pencil as shown on the right.  
To remove the rough edges, press the  
side of the pen or pencil against the  
inside and outside edges of the disc.  
• A disc should always be kept in its  
case when not in use to prevent from  
damaging.  
• Do not place discs in the following  
places:  
1. Direct sunlight  
2. Dirty, dusty and damp areas  
3. Near car heaters  
4. On the seats or dashboard  
Disc Cleaning  
Rough spots on  
outside edge  
Use a dry soft cloth to wipe the surface.  
If the disc is quite dirty, use a soft cloth  
slightly moistured with isopropyl (rubbing)  
alcohol. Never use solvents such as  
benzine, thinner or conventional record  
cleaners as they may mar the surface of  
the disc.  
Ball point pen  
or pencil  
Note:  
A disc may become somewhat scratched  
(although not enough to make it  
unusable) depending on your handle it  
and conditions in the usage environment.  
Note these scratches are not an  
indication of any problem with the player.  
Rough spots  
on inside edge  
3
TAPE NOTES  
1. Take care of your tape cassette to preserve the quality of the recordings. Do not  
allow them to be exposed to direct sunlight. Store them in a place protected from  
dirt and dust and avoid handing with greasy or oily hands. Also, keep the away  
from magnets, and motors of the permanent magnet type.  
2. It is not advisable to use cassette tapes longer than C-60 (30 minutes per side) in  
automobile players, since the tape is too thin and tends to become easily entangled.  
Always remove cartridge from your tape player as soon as play is finished.  
3. The capstan and tape head should be cleaned about once every six months with  
a soft cloth or cotton-wool swab, moistened with alcohol. This will serve to maintain  
the richness and clarity of sound, and prevent loss of volume. Do not use a  
screwdriver, or ferrous metal rod, in carrying out the above cleaning. See illustration.  
4. A loosely wound cassette tape will get damaged. Prior to using such tape, tighten  
it in a manner as guided by Fig. A carelessly would cassette tape will cause  
unnecessary pressure on the tape resulting in the cassette springing out while the  
tape is running. For prevention rewind the tape through fast forwarding or rewinding.  
4
INSTALLATION  
NOTES:  
Choose the mounting location where the unit will not interfere with the normal  
driving function of the driver.  
Before finally installing the unit, connect the wiring temporarily and make sure it is  
all connected up properly and the unit and the system work properly.  
Use only the parts included with the unit to ensure proper installation. The use of  
unauthorized parts can cause malfunctions.  
Consult with your nearest dealer if installation requires the drilling of holes or other  
modifications of the vehicle.  
Install the unit where it does not get in the driver’s way and cannot injure the  
passenger if there is a sudden stop, like an emergency stop.  
If installation angle exceeds 30˚ from horizontal, the unit might not give its optimum  
performance.  
30˚  
Avoid installing the unit where it would be subject to high temperature, such as from  
direct sunlight, or from hot air, from the heater, or where it would be subject to dust,  
dirt or excessive vibration.  
DIN FRONT/REAR-MOUNT  
This unit can be properly installed either from “Front” (conventional DIN Front-mount)  
or “Rear” (DIN Rear-mount installation, utilizing threaded screw holes at the sides of  
the unit chassis). For details, refer to the following illustrated installation methods.  
5
INSTALLATION  
1. Install brackets and screws removed from your old radio (not provided with this  
unit).  
2. Slide unit and frame into dash opening.  
3. Trim ring has precutgrooves on the back of it. The size of the trim ring can be  
reduced (made smaller) for different types of installations. Hold the trim ring firmly  
in one hand, and using a pair of pliers, grasp the trim ring above the score line  
(groove) and bend gently back and forth a couple of times. Then the piece should  
break away.  
4. Install dash panel.  
5. Install faceplate by fitting left edge into position then pushing right edge closed.  
2
3
4
1
5
6
INSTALLATION  
CAUTION: DO NOT INSTALL THE DETACHABLE PANEL BEFORE  
CONNECTING THE WIRE.  
1. The unit is designed for negative terminal of the battery which is connected to the  
vehicle metal. Please confirm it before installation.  
2. If the car interior is extremely hot, as after being parked in the sun, do not use the  
player until the car has been driven for a while to cool off the interior.  
3. Press the REL button to take away the front panel (see fig.1), and put it in the protective  
case (see fig.2) safe keeping.  
4. Install the front panel back into its bracket and then push it back to the position for  
playing (see fig.3).  
Fig 1  
Fig 2  
Fig 3  
7
ELECTRIC CONNECTION  
MAIN UNIT  
ANTENNA CONNECTOR  
FUSE  
RED  
IGNITION  
SWITCH (B+)  
FUSE  
MEMORY  
BACK-UP (B+)  
YELLOW  
BLACK  
GROUND (B–)  
FUSE  
POWER  
BLUE  
ANTENNA  
WHITE  
GREY  
FRONT Lch  
SPEAKER  
FRONT Rch  
SPEAKER  
WHITE/BLACK  
GREEN  
GREY/BLACK  
VIOLET  
REAR Lch  
SPEAKER  
REAR Rch  
SPEAKER  
GREEN/BLACK  
VIIOLET/BLACK  
DESCRIPTION OF RCA JACK (ON THE BACK OF THE UNIT)  
FRONT RCA OUTPUT  
V. OUT = VIDEO OUT  
AUXILIARY IN  
V. IN = VIDEO IN  
FL OUT = FRONT LEFT AUDIO OUT  
FR OUT = FRONT RIGHT AUDIO OUT  
L. IN = LEFT AUDIO IN  
R. IN = RIGHT AUDIO IN  
REAR RCA OUTPUT  
V. OUT = VIDEO OUT  
COX = COAXIAL OUT  
SW = SUB-WOOFER OUT  
RL OUT = REAR LEFT AUDIO OUT  
RR OUT = REAR RIGHT AUDIO OUT  
8
REMOTE CONTROL  
11  
13  
1
12  
14  
POWER  
MODE  
SETUP  
CLK  
2
STOP  
PLAY/PAUSE  
ANGLE  
MUTE  
3
5
7
BAND  
OSD  
ST/MO  
REPEAT  
4
6
8
15  
17  
19  
TITLE/PBC  
A/P  
LO/DX  
16  
18  
EQ  
SEL  
+
UP  
F. FWD  
NEXT  
VOL  
ENTER  
DN  
20  
21  
F. BWD  
PREV.  
VOL  
-
9
1
5
2
6
9
3
4
7
8
SW  
MENU  
+10  
10  
0
22  
1. CLK  
2. MODE  
3. SETUP  
Press it to change the display to clock display.  
Press it to change between radio or disc mode.  
Display the SETUP menu.  
4. OSD (BAND) Display statistical disc information during playback (To change the  
band in radio stations)  
5. ST/MO (AUDIO) Press it to select STEREO or MONO (In disc stations, press it to  
changing of the AUDIO soundtrack on multi-audio soundtrack DVD  
disc. Changing of the sound mode of the VCD/CD disc)  
6. SEL  
Press it to change audio mode through Volume, Bass, Treble, Balance  
and Fader modes.  
7. TITLE/PCB Display the TITLE menu that is stored in DVD disc changing  
(A/P)  
between PBC ON and PBC OFF on the VCD disc. (Auto store and  
preset scan function in radio stations.)  
8. VOL+/VOL- Press it to adjust volume level.  
9.  
/ / /  
Cursor buttons in MENU mode.  
Press it to display the root menu of the DVD disc./ Press and hold for  
10. MENU/  
SUBWOOFER more than 2 seconds can have subwoofer.  
11. STOP  
Press it to stop playback.  
12. PLAY/PAUSE Press once to pause a play, press again to resume playback.  
13. POWER  
14. MUTE  
15. REPEAT  
16. ANGLE  
17. EQ  
Press it to turn on the unit, press it again to turn off.  
Press it to mute down the sound.  
Switch the Repeat mode of DVD/VCD/CD disc.  
Changing of the view angle on multi-angle DVD disc  
Press it to change the equalization as jazz, classic, pop, rock.  
18. SUBTITLE Changing of the SUBTITLE language on multi-subtitle language  
(LO/DX)  
DVD disc. In radio mode, press this button for distance reception  
when you are located at weak signal location, depress it for stronger  
signal.  
19  
/
Press  
to skip to the next track & press  
to skip back one track.  
20. ENTER  
Confirm the Track/Chapter selected with the number key or selected  
with the cursor buttons on TV screen.  
Numeric buttons  
21. 0 - 9  
22. +10  
Press it to select 10th digits  
9
REMOTE CONTROL  
Preparing the Remote Control  
Inserting the Batteries  
1. Open the battery compartment cover.  
2. Insert the new batteries.Make sure that the positive and negative terminals of the  
batteries are oriented indicated.  
3. Close the cover  
Using the Remote Control  
Face the remote control towards the player front face IR mark (remote control signal  
receiver).  
Operation angle: About 30 degree in each the direction of the front of the IR mark.  
To prevent damage to the unit, be sure to follow the connection diagram  
(page 8).  
10  
BASIC OPERATION  
1
16  
5
19 13  
CAR DVD/VCD/CD/MP3 CASSETTE RECEIVE  
ST  
TAPE IN  
2
18  
3
6
7
8
14 15 12  
9
10  
11  
4
20  
17  
26  
24  
25  
23  
21  
22  
11  
BASIC OPERATION  
1. OPEN BUTTON  
Press it to flip down the front panel then you can insert the TAPE into the tape  
compartment.  
2-3. VOL +/ VOL- & SEL BUTTON  
Press it to change audio mode through volume, bass, treble, balance, and fader  
modes. Use VOL +/ VOL- buttons to adjust the selected mode. When mode has  
not been adjusted for several seconds, display returns to normal radio or CD display.  
VOL  
BAS  
TRE  
BAL  
FAD  
A. Volume: Adjust volume level by using VOL +/ VOL- buttons.  
Note:The unit is initially set to volume mode.  
B. Bass: Press SEL button one time. Adjust bass level by using VOL +/ VOL- buttons.  
C. Treble: Press SEL button two times. Adjust treble level by using VOL +/ VOL-  
buttons.  
D. Balance: Press SEL button three times. Adjust sound balance between left and  
right speakers by using VOL +/ VOL- buttons.  
E. Fader: Press SEL button four times. Adjust sound balance between front and  
rear speakers by using VOL +/ VOL- buttons.  
4. BAND BUTTON  
In RADIO mode, press the BAND button on the front panel or on the remote controller  
to select your desired radio band and word which band is selected will be displayed  
on LCD. Press it to change the bands as below:  
FM  
MW  
LW  
FM  
MW  
FM  
AM  
For 3 Bands (Europe)  
For 2 Bands (Europe)  
For 2 Bands (USA)  
5. DISC COMPARTMENT  
Insert the disc into the disc compartment and the mechanism will now engage into  
the disc play mode.  
6-7-8-9-10-11. PRESET STATION  
A. To memorize the current frequency, press any one of the six preset buttons[1-6]  
on the front panel or on the remote controller hold for more than 2 seconds.  
B. To recall the preset memory, press one of the preset buttons [1-6].  
C. Press 1/TOP button to select the first track/ chapter to play.  
a. In the state of VCD/CD/MP3 disc playing, press the button on the front panel  
to select the first track/chapter to play. (depend on the disc used for VCD)  
b. In the state of DVD disc playing, the 1TOP button is not available.  
D. Press 2/RPT button to select repeat mode as follow.  
DVD:  
CHAPTER REPEAT ON  
TITLE REPEAT ON  
REPEAT OFF  
VCD/CD:  
REP-ONE  
REP-ALL  
12  
BASIC OPERATION  
a. Continuously repeat at the current chapter/track, when selected REP-ONE  
mode.  
b. Select REP-ALL mode to continuously repeat all chapter/track on the current  
disc.  
c. REPEAT feature does not support VCD2.0 (with PBC ON).  
E. Press 3/INT button to scan disc.  
a. In the state of VCD/CD disc playing, press the 3/INT button on the front panel  
to play the previous 10 seconds part of each track/chapter on disc (depend  
on the disc used for VCD).  
b. In the state of DVD/MP3 disc playing, the 3/INT button is not available.  
F. Press 4/RDM to play disc in random.  
a. In the state of VCD/CD/MP3 disc playing, press the 4/RDM button on the front  
panel to play in random or select DISC REP. (depend on the disc used for VCD)  
b. In the state of DVD disc playing, the 4/RDM button is not available.  
12. AS/PS BUTTON  
When shortly pressing the APS button on the front panel or the A/P button on the  
remote controller, the radio searches for each preset station. When the field strength  
level is more than the threshold level of stop level, the radio is holding at that preset  
number for few seconds with releasing mute, and then searches again.  
In FM band, FM 1,FM 2 and FM 3 is checked one at a time. When long pressing  
the APS or A/P button (more than 1 second), the radio searches from the current  
frequency and checks the signal strength level until 1 cycle search is finished. And  
then 6 strongest stations are preset to the corresponding preset number.  
The AS operation is implemented in the each band of selected band. When the AS  
operation is finished, the radio executes the preset scan.  
13. MU BUTTON  
Press it to mute down sound. Press it again to release this mode and recover previous  
volume level.  
14.CLK BUTTON  
Press it to change the display to clock display. Press it again to return to previous  
display. In clock display, press and hold for about 2 seconds until the hour display  
flashes. Press VOL +/ VOL- to adjust hours, press CLK button to flash mintue then  
press VOL +/ VOL- to adjust minutes.  
15. PWR BUTTON  
Press it to turn on the unit. Press it again to turn off.  
16.  
BUTTON  
Pressing during playback will stop play temporary. Return to normal playback,  
press once again.  
13  
BASIC OPERATION  
17.  
/
BUTTONS  
A. When long pressing the  
the speed of rapid forward/reverse changes according to the disc as follow.  
/
button (more than 2 seconds) during play,  
DVD:  
Normal Playback  
VCD/CD:  
Normal Playback  
2X  
4X  
6X  
8X  
2X  
3X  
4X  
MP3:  
Normal Playback  
2X  
4X  
B. Shortly press the  
one track.  
/
button during playback to skip to next track or back  
Note: For some VCD2.0 discs (PBC-playback control),  
be unavailable.  
and  
buttons may  
C. Press UP or DN button on the remote controller or  
/
on the front panel to  
manually tune up or down for your desired station. Press them hold for more  
than 2 seconds to automatically tune up or down for the stronger station.  
18. MOD BUTTON  
A. When there is tape and disc in the unit. Press it repeatedly to select AUX IN,  
RADIO, DISC, TAPE mode.  
B. When there is tape but no disc in the unit, you can select AUX IN, RADIO, TAPE  
mode.  
C. When there is disc but no tape in the unit, you can select AUX IN, RADIO, DISC  
mode.  
D. When there is no tape and disc in the unit, you can select AUX IN, RADIO mode.  
19. EJECT BUTTON OF DISC  
Press it to eject the disc from the CD compartment.  
20. RELEASE BUTTON  
Press it to detachable the removable faceplate.  
21. CASSETTE COMPARTMENT  
Holding the cassette tape lengthwise, insert it into the compartment, the tape  
mechanism will now engage into the cassette play mode.  
22. PROGRAM BUTTON  
To fast forward or fast rewind the cassette tape, push down the corresponding button  
into the locking position. If fast forward button is pressed, it can be released by  
pushing down the rewind button and vice versa.  
Push down these two buttons simultaneously to change the playback direction.  
23. EJECT BUTTON OF TAPE  
Push down to eject the cassette tape.  
14  
BASIC OPERATION  
24. FLASHING LED  
If the front panel is not on the main unit, LED will be flashing.  
25. RESET BUTTON  
RESET button is placed on the housing and must be activated with either a ballpoint  
pen or thin metal object. The RESET button is to be activated for the following  
reasons:  
A. Initial installation of the unit when all wiring is completed.  
B. All the function buttons do not operate.  
C. Error symbol on the display.  
Note: If press RESET button, the unit can’t work yet, please use a cotton swab  
soaked in isopropyl alcohol to clean the socket on the back of the front panel.  
26. THE CHANGE-OVER SWITCH OF FREQUENCY (option)  
Slide it you can select the USA or EUROPE radio frequancy.  
MP3 Disc Play  
1. MP3 disc is playing as the format of FOLDER by FOLDER.  
For example:  
MP3 PLAYER  
ROOT  
ROOT  
MP3 MUSIC  
SKY  
0
1
MP3 HEAR YOUR  
Use / / / to select the item or folder, then press ENTER button.  
Pressing REPEAT button repeatedly can select three kinds of repeat play mode.  
2. REP-ONE:  
Play the same song over and over again.  
3. FOLDER REPEAT:  
Play all songs in the current directory in sequence, over and over again.  
4. DISC REPEAT:  
Play all songs in the disc over and over again.  
In the playback, use  
When long pressing the  
or  
to skip an item ahead or back.  
to fast rapid forward/reverse.  
/
Note: The FOLDER cannot be selected during playing. It can be selected after  
(Stop) button pressed.  
15  
BASIC OPERATION  
c. Press OSD for the third time:  
On-Screen Display Function  
Press the OSD button during playback to  
display the contents of the current disc  
on the screen.  
T:01/18 P: 00:00:25 LR DISC  
TOTAL ELAPSED  
A. Example for DVD:  
d. Press OSD for the fourth time:  
a. Press OSD for the first time:  
T:01/18 P: 00:00:25 LR DISC  
TOTAL REMAIN  
TITLE 01/03 CHAPTER 002/025  
P:00:00:25 TITLE ELAPSED  
e. Press OSD for the fifth time:  
The message on the screen will be  
cleared for SVCD and VCD.  
Title Number, Total Title Number,  
Chapter Number, Total Chapter  
Number of this Title of the disc  
currently being played will be shown  
on the screen, along with the elapsed  
time.  
Note: For CD and Mp3, the  
message will always display on  
the screen.  
C. Example for MP3:  
Each time OSD is pressed, the  
message displayed on screen  
changesas follows:  
b. Press OSD for the second time:  
TITLE 01/03 CHAPTER 002/025  
P: 00:00:25 TITLE REMAIN  
SINGLE ELAPSED  
SINGLE REMAIN  
c. Press OSD for the third time:  
TITLE 01/03 CHAPTER 002/025  
P:00:00:25 CHAPTER ELAPSED  
d. Press OSD for the fourth time:  
TITLE 01/03 CHAPTER 002/025  
P: 00:00:25 CHAPTER REMAIN  
e. Press OSD for the fifth time:  
The message on the screen will be  
cleared.  
B. Example for VCD/SVCD/CD:  
a. Press OSD for the first time:  
T:01/18 P: 00:00:25 LR DISC  
SINGLE ELAPSED  
b. Press OSD for the second time:  
T:01/18 P: 00:00:25 LR DISC  
SINGLE REMAIN  
16  
BASIC OPERATION  
Multi-subtitle Language Function  
(For DVD only)  
Press SUBTITLE during playback. Each  
time the button is pressed, number of the  
subtitle language changes in sequential  
order.  
Notes: The language number is different  
according to the disc. Some discs only  
contain one subtitle language. When no  
different subtitle language are recorded,  
will be displayed at screen left top  
corner.  
Multi-audio Language Function  
A. DVD: Press AUDIO during  
playback.  
Each time the button is pressed,  
number of the audio soundtrack  
language changes on sequential order.  
Notes:The language number is  
different according to the disc. Some  
disc only contain one language  
soundtrack. When no different  
language soundtrack are recorded,  
will be displayed at screen left top  
corner.  
Multi-angle Function (For DVD only)  
Press ANGLE during playback. Each time  
the button is pressed, number of the angle  
changes in sequential order.  
Notes: The angle number is different  
according to the disc.The function only  
work for discs having scenes recorded at  
different angles. When no different angle  
are recorded, will be displayed at screen  
left top corner.  
B. VCD: Press AUDIO during  
playback. It is possible to switch  
the sound between monaural and  
stereo sound.  
LEFTVOCAL  
RIGHT VOCAL  
MONO LEFT  
STEREO  
MONO RIGHT  
C. CD: Press AUDIO during  
playback. It is possible to switch  
the sound between monaural and  
stereo sound.  
MONO LEFT  
MONO RIGHT STEREO  
TITLE Menu Function  
A. DVD: If the DVD has multiple titles  
recorded on the disc. It can select  
preferred title from the title menu  
to start playback.  
a.Press TITLE during playback.  
The title menu is display.  
b.Press the cursor button shown  
in TV screen, select preferred  
title by the cursor button and  
confirmed by ENTER key.  
B. VCD: Press MENU button while  
the disc is playing, you can switch  
between "PBC on" and "PBC off"  
mode.  
17  
SETUP  
INITIAL SETUP  
GENERAL SETUP  
--- MAIN PAGE---  
--- GENERAL PAGE ---  
GENERAL SETUP  
SPEAKER SETUP  
AUDIO SETUP  
TV DISPLAY  
PIC MODE  
NORMAL/PS  
NORMAL/LB  
WIDE  
ANGLE MARK  
OSD LANG  
CAPTIONS  
SCR SAVER  
PREFERENCES  
EXIT SETUP  
1. Press SETUP in the stop mode.  
(Press the stop button twice to ensure  
the player under STOP mode.)  
MAIN PAGE  
TV Screen  
2. The initial SETUP menu is displayed.  
4:3  
Wide (16:9)  
Video Material  
Normal  
Pan Scan  
Letter-box  
4:3  
3. Select the preferred item by using the  
/ buttons.  
16:9  
4. Press ENTER buttons.  
A. GENERAL SETUP  
This setup page includes all the  
item of TV display & audio output  
feature. The detail please refer to  
GENERAL SETUP MENU.  
1. TV DISPLAY SETUP  
This is to select the appropriate TV  
aspect (4:3 or 16:9) according to the  
connected TV set.  
B. SPEAKER SETUP  
Normal/PS (For 4:3 TV)  
This is to activate the audio output  
from DOLBY AC3 5.1 DOWNMIX  
to 2 channel mode. Please refer to  
SPEAKER SETUP MENU.  
Played back in the PAN & SCAN style.  
(If connected to wide-screen TV, the  
left and right edges are cut off.)  
Normal/LB (For 4:3 TV)  
C. AUDIO SETUP  
Played back in letterbox style.  
(If connected to wide-screen TV, black  
bands appear at top and bottom of  
the screen.)  
This setup page includes all the  
items for AUDIO. Please refer to  
AUDIO SETUP MENU.  
D. PREFERENCE SETUP  
Wide (For 16:9 TV)  
Select when a wide-screen TV set is  
connected.  
This setup page includes all the  
configuration of support feature.  
The detail please refer to  
PREFERENCES SETUP MENU.  
18  
SETUP  
--- GENERAL PAGE ---  
--- GENERAL PAGE ---  
TV DISPLAY  
TV DISPLAY  
PIC MODE  
AUTO  
PIC MODE  
ANGLE MARK  
OSD LANG  
CAPTIONS  
SCR SAVER  
HI-RES  
ANGLE MARK  
OSD LANG  
CAPTIONS  
SCR SAVER  
N-FLICKER  
ENGLISH  
MAIN PAGE  
MAIN PAGE  
2. PIC MODE SETUP  
4. OSD LANG TYPE SETUP  
Select the preferred OSD language by  
using the / buttons.  
Select AUTO, the player PIC mode will  
depend on DVD disc.  
Select HI-RES format for best image  
resolution.  
Select N-FLICKER format on format  
on image or picture under noise affect.  
--- GENERAL PAGE ---  
--- GENERAL PAGE ---  
TV DISPLAY  
PIC MODE  
TV DISPLAY  
PIC MODE  
ANGLE MARK  
OSD LANG  
CAPTIONS  
ON  
ANGLE MARK  
OSD LANG  
OFF  
CAPTIONS  
ON  
SCR SAVER  
SCR SAVER  
OFF  
MAIN PAGE  
MAIN PAGE  
3. ANGLE MARK DISPLAY SETUP  
5. CAPTIONS SETUP  
If it is set to ON, when the multi-angle  
Activate the CAPTIONS feature by  
selecting ON. And release this feature  
by selecting OFF.  
DVD disc is playing,  
(the angle  
mark) will appears on the screen; if it  
is set to OFF, the mark will not appear.  
19  
SETUP  
--- GENERAL PAGE ---  
AUDIO SETUP  
--- AUDIO SETUP ---  
TV DISPLAY  
PIC MODE  
AUDIO OUT  
OP MODE  
ANALOG  
ANGLE MARK  
OSD LANG  
CAPTIONS  
SCR SAVER  
SPDIF/RAW  
SPDIF/PCM  
LPCM OUTPUT  
DYNAMIC  
ON  
OFF  
MAIN PAGE  
SCR SAVER SETUP  
Select the SCR SAVER output ON/OFF.  
MAIN PAGE  
1. AUDIO OUT  
SPEAKER SETUP  
This is to activate the audio output  
from ANALOG mode to SPDIF/RAW  
mode to SPDIF/PCM mode.  
--- SPEAKER SETUP PAGE ---  
DOWNMIX  
LT/RT  
--- AUDIO SETUP ---  
STEREO  
AUDIO OUT  
MAIN PAGE  
OP MODE  
LINE OUT  
LPCM OUTPUT  
DYNAMIC  
RF REMOD  
This is to activate the audio output from  
DOLBY AC3 5.1 DOWNMIX to 2 channel  
mode. Select the preferred SPEAKER  
connection by using the cursor buttons.  
- Select the LT/RT to activate the Dolby  
surround compatible output.  
MAIN PAGE  
2. OP MODE  
There are two operating modes for the  
Dolby Digital decoder: LINE OUT and  
RF REMOD.  
- Select the STEREO to activate simple  
stereo mode.  
20  
SETUP  
--- AUDIO SETUP ---  
PREFERENCES SETUP  
--- PREFERENCES PAGE ---  
TV TYPE  
MULTI  
NTSC  
PAL  
AUDIO OUT  
AUDIO  
OP MODE  
SUBTITLE  
DISC MENU  
PARENTAL  
PASSWORD  
DEFAULTS  
SMART NAV  
MAIN PAGE  
LPCM OUTPUT  
DYNAMIC  
LPCM 48K  
LPCM 96K  
MAIN PAGE  
1. TV TYPE SETUP  
3. LPCM OUTPUT  
This player can play discs recorded in  
either PAL or NTSC format.  
Select NTSC format, when you  
connected to NTSC TV.  
Select the LPCM OUTPUT between  
LPCM 48K and LPCM 96K.  
Select PAL format, when you  
connected to PAL TV.  
--- AUDIO SETUP ---  
Select AUTO format, the player TV  
output format will according to the  
DVD disc format.  
AUDIO OUT  
FULL  
6/8  
OP MODE  
--- PREFERENCES PAGE ---  
LPCM OUTPUT  
DYNAMIC  
TV TYPE  
4/8  
AUDIO  
ENGLISH  
FRENCH  
SPANISH  
CHINESE  
JAPANESE  
2/8  
SUBTITLE  
DISC MENU  
PARENTAL  
PASSWORD  
DEFAULTS  
SMART NAV  
MAIN PAGE  
OFF  
MAIN PAGE  
4. DYNAMIC RANGE CONTROL  
Select DRC and adjust the dynamic  
range of a Dobly Digital encoded  
program. There are 8 steps between  
full compression and off compression.  
2. AUDIO LANGUAGE SETUP  
Select the preferred AUDIO sound-  
track by using the cursor buttons.  
21  
SETUP  
--- PREFERENCES PAGE ---  
--- PREFERENCES PAGE ---  
TV TYPE  
TV TYPE  
1 G  
AUDIO  
AUDIO  
2
SUBTITLE  
DISC MENU  
PARENTAL  
PASSWORD  
DEFAULTS  
SMART NAV  
MAIN PAGE  
ENGLISH  
FRENCH  
SPANISH  
CHINESE  
JAPANESE  
OFF  
SUBTITLE  
DISC MENU  
PARENTAL  
PASSWORD  
DEFAULTS  
SMART NAV  
MAIN PAGE  
3 PG  
4 PG 13  
5
6 PG-R  
7 NC-17  
8 ADULT  
NO_PARENTAL  
3. SUBTITLE LANGUAGE SETUP  
Select the preferred SUBTITLE  
5. PARENTAL  
Select suitable parental guidance by  
the cursor buttons and confirmed by  
pressing ENTER button.  
language by using the cursor buttons.  
--- PREFERENCES PAGE ---  
--- PREFERENCES PAGE ---  
TV TYPE  
AUDIO  
TV TYPE  
AUDIO  
SUBTITLE  
SUBTITLE  
DISC MENU  
PARENTAL  
DISC MENU  
PARENTAL  
PASSWORD  
DEFAULTS  
SMART NAV  
MAIN PAGE  
ENGLISH  
FRENCH  
SPANISH  
CHINESE  
JAPANESE  
PASSWORD  
DEFAULTS  
SMART NAV  
MAIN PAGE  
CHANGE  
4. DISC MENU LANGUAGE SETUP  
Select the preferred DISC MENU  
language by using the cursor buttons.  
6. PASSWORD  
Select the change and press ENTER  
button. Type the old password (The  
initial factory code is 3308) and key  
in 4 characters password now you  
want to use, and retype again to  
confirm key in correctly.  
22  
SETUP  
--- PREFERENCES PAGE ---  
DEFAULTS TABLE  
TV TYPE  
General Setup TV Display  
Normal/PS  
AUTO  
PIC Mode  
AUDIO  
Angle Mark ON  
SUBTITLE  
DISC MENU  
PARENTAL  
PASSWORD  
DEFAULTS  
SMART NAV  
MAIN PAGE  
OSD Language English  
Captions  
OFF  
SCR Saver OFF  
Speaker Setup Downmix  
Stereo  
Audio Setup Audio Out  
OP Mode  
Analog  
Line Out  
RESET  
Dynamic  
LPCM Out  
LPCM 96K  
MULTI  
Preferences TV Type  
Audio  
7. DEFAULTS  
English  
English  
Select reset to become factory initial  
setting.  
Subtitle  
DISC Menu English  
Parental  
NO PARENTAL  
3308  
--- PREFERENCES PAGE ---  
Password  
Smart Nav  
With Menu  
TV TYPE  
AUDIO  
SUBTITLE  
DISC MENU  
PARENTAL  
PASSWORD  
DEFAULTS  
SMART NAV  
MAIN PAGE  
NO MENU  
WITH MENU  
8. SMART NAV  
In this item, you can select NO MENU  
mode or WITH MENU mode.  
23  
SPECIFICATIONS  
Supply voltage  
Current consumption  
Signal system  
: 12V DC (11V-15V)  
: Less than 10A  
: Compositive video 1.0Vp-p 75  
: (1) DVD-VIDEO disc  
Discs played  
5”(12 cm) single-sided, single-layer  
5”(12 cm) single-sided, double-layer  
(2) Compact disc (CD-DA,VIEDO CD)  
5”(12 cm) disc  
Audio Signal Output  
Characteristics  
: 2ch & 4ch line out  
: (1) Frequency Response:  
(2) S/N Ratio:  
20 Hz-20 kHz  
90 dB (JIS)  
(3) Wow and Flutter:  
Below measurable limits  
TAPE SECTION  
Wow & Fluter  
S/N Ratio (Normal)  
Separation  
: 0.3%  
: 52 dB  
: 45 dB  
Frequancy response  
: 50Hz-15KHz  
RADIO SECTION  
For 3 Bands  
(Europe)  
FM  
For 2 Bands  
(Europe)  
FM  
For 2 Bands  
(U.S.A.)  
FM  
Frequency Coverage  
IF  
: 87.5 to 108 MHz 87.5 to 108 MHz 87.5 to 107.9 MHz  
: 10.7 MHz  
Sensitivity (S/N = 30 dB) : 15 dBu  
10.7 MHz  
15 dBu  
10.7 MHz  
15 dBu  
MW  
MW  
AM  
Frequency Coverage  
IF  
: 522 to 1620 KHz 522 to 1620 KHz 530 to 1710 KHz  
: 450 KHz  
Sensitivity (S/N = 20 dB) : 40 dBu  
450 KHz  
40 dBu  
450 KHz  
40 dBu  
LW  
Frequency Coverage  
IF  
: 144 to 290 KHz  
: 450 KHz  
Sensitivity (S/N = 20 dB) : 45 dBu  
Note:  
Specifications and design are subject to modification, without notice, due to improvements  
in technology.  
24  
TROUBLE SHOOTING  
Before going through the check list, check wiring connection. If any of the problems  
persist after check list has been made, consult your nearest service dealer.  
Symptom  
No power.  
Cause  
Solution  
The car ignition switch is  
not on.  
If the power supply is properly  
connected to the car accessory  
terminal,switch the ignition key  
to “ACC“.  
The fuse is blown.  
Replace the fuse.  
Disc cannot be Presence of disc inside the  
Remove the disc in the player,  
Then put a new one  
loaded or  
ejected.  
player  
Inserting the disc in reverse  
direction.  
Insert the compact disc with  
the label facing upward.  
The disc is extremely dirty or  
defective  
Clean the disc or try to play a  
new one.  
Temperature inside the car  
is too high.  
Cool off or until the ambient  
temperature return to normal.  
Condensation.  
Leave the player off for an hour  
then try again.  
No sound.  
Volume is in minimum.  
Adjust volume to a desired level.  
Check wiring connection.  
Wiring is not properly  
connected.  
Sound skips.  
The installation angle is  
more than 30 degrees.  
Adjust the installation angle less  
than 30 degrees.  
The disc is extremely dirty  
or defective disc.  
Clean the compact disc, then  
try to play a new one.  
The operation  
keys do not  
work.  
The built-in microcomputer  
is not operating properly  
due to noise.  
Press the RESET button.  
Front panel is not properly  
fixed into its place.  
The radio does The antenna cable is not  
Insert the antenna cable firmly.  
not work.  
connected.  
The signals are too weak.  
Select a station manually.  
This product incorporates copyright protection technology that is protected by method  
claims of certain U.S. patents and other intellectual property rights owned by  
Macrovision Corporation and other rights owners.Use of this copyright protection  
technology must be authorized by Macrovision Corporation, and is intended for home  
and other limited viewing uses only unless otherwise authorized by Macrovision  
Corporation. Reverse engineering or disassembly is prohibited.  
25  
88-V2940-01  

PYLE Audio View Series PLVRL6400 User Manual
PYLE Audio PYLE Blue Wave Series PLA2840 User Manual
Planar Systems Car Video System PLL1900W User Manual
Pentax PLP 602 User Manual
Panasonic NV GS150 User Manual
Nikon Monarch X 4 16x50 SF User Manual
Kenwood MD RECEIVER KMD 870R User Manual
JVC High Definition Camcorder GZVX700BUS User Manual
JVC HDV GY HD100 User Manual
JVC GY HM790CHU User Manual